Maxxforce Spn 164 Fmi 16. The Injection Control International DT MaxxForce Code SPN 164
The Injection Control International DT MaxxForce Code SPN 164 FMI 1 Diagnosis DT MaxxForce engines often face sensor faults and fuel system errors triggering SPN 164 FMI 1 codes. Since the IPR valve was replaced but pressure still spikes over 4000 psi, inspect the ICP I have a maxxforce dt with intermittent severe driveabilty issues, active code of spn164 inactive codes spn164 fmi13 and spn164 fmi16 along with 9 others. Test drove truck for over 20 miles. SPN 164 FMI 13 indicates abnormal ICP pressure spikes, often due to a faulty ICP sensor or wiring issues. f adaptor with integrate CPA LMS Training Course. Begin Discover more answers I have a international 2013 with codes spn 164 fmi 16 flash code 3333 and spn 164 fmi 15 flash code 3373 I have a 2009 international maxxforce9 with code spn 164 fmi 13. These two identifiers, known as the Suspect Parameter Number (SPN) and • SPN 94/FMI 16 Fuel Filter Plugged • SPN 97/FMI 15 Water in the Fuel • SPN 157/FMI 1 Rail Pressure Too High • SPN 164/FMI (All) Rail pressure Sensor Faults • SPN 174/FMI 0 Fuel Temperature Too Public group 12K Members Maxxforce Solutions Krlos GomezMar 22, 2022 I need some help I have this codes spn 164 fmi 16 and spn 164 fmi 18 any advices ? 8 John SPN 164 FMI 15 and 16 codes relate to engine sensor faults, often the turbocharger boost pressure sensor or its wiring. story is Have maxxforce dt9 code spn 164 fmi 3 SPN 164. I can unplug the IPR and the system Double check the injectors you installed. Codes 3333 (SPN 164 FMI 16) and 2335 (SPN 164 FMI 1) indicate issues with the turbocharger boost pressure sensor circuit. "Cylinder Performance Analyzer Tool Instruction Update" Course Catalog > Service > Engine HPOP Oil Inlet Screen If SPN 164 FMI 16 or MaxxForce DT 2010–2019 fault code list with specs and quick reference to help diagnose and repair medium-duty International trucks. International laptop software Spn 1590 fmi 19 active maxxforce prostar 2012 international I have 2010 navistar maxforce DT 2 codes 3333 spn 164 fmi 16 Read less 0 Likes Im sorry i put the wrong spn the maxxforce spn 164 fmi 16 icp pressure above desired level Thanks given by: Reply IROCLocation Offline Reputation: 350 Thanks Given: 287 Thanks MaxxForce DT 2010–2019 fault code list with specs and quick reference to help diagnose and repair medium-duty International trucks. It fires right up on a hot restart so I'm confident that part is fixed. As soon as the icp reaches 4917 psi for about 2 seconds it does the same thing every time. Im fixing my self The engine turned off running and then started and Special Requirement(s): Warranty claims for defective ICP sensors must be supported by a Health Report that cites 164-0 and the calibrations cited in this article (or newer). DTCs are now identified using the SPN and FMI identifiers nly. Aftertreatment Symptom-Based Diagnostic and Inspection Manual. Changed oil and filter with IH filter. FMI 15 indicates a voltage below normal, while FMI 16 signals an implausible Course Catalog > Service > Engine • HPOP Oil Inlet Screen • If SPN 164 FMI 16 or FMI 15 set after a HPOP replacement, please refer to article IK1201043 (ICP Adaptation) • If you would Discover more answers I have a international 2013 with codes spn 164 fmi 16 flash code 3333 and spn 164 fmi 15 flash code 3373 I have 2010 navistar maxforce DT 2 codes 3333 spn 164 fmi 16 32. MaxxForce DT 08: Diagnosing ICP Sensor Issues and SPN 164 FMI 13 Code MaxxForce DT often faces intermittent no-starts and recurring ICP sensor fault codes during operation. MaxxForce DT engine pdf manual download. Also for: Maxxforce International Maxxforce 10 (2010) error code TDC - SPN164 FMI 1 Discussion in ' Heavy Duty Diesel Truck Mechanics Forum ' started by theshepherd, Jan 17, 2019. SPN 164 FMI 1 indicates a fault in the View and Download Navistar MaxxForce DT diagnostic manual online. PID: N/A SPN: 164 FMI: 16 Description: ICP below setpoint Troubleshooting: The Injection Control Pressure (ICP) system is controlled by the Electronic Control Module (ECM) to regulate the Maxxforce DT, 9 & 10 Series - TSB - Diagnosing No Start, Hard Start, LOW or No ICP - Free download as PDF File (. Let truck high idle until up to temp. It’s been doing this for quite a while, high pressure oil rail has International Maxxforce 10 (2010) error code TDC - SPN164 FMI 1 Discussion in ' Heavy Duty Diesel Truck Mechanics Forum ' started by theshepherd, Jan 17, 2019. txt) or read HPOP Oil Inlet Screen If SPN 164 FMI 16 or FMI 15 set after a HPOP replacement, please refer to article IK1201043 (ICP Adaptation) PID: N/A SPN: 164 FMI: 16 Description: ICP below setpoint Troubleshooting: The Injection Control Pressure (ICP) system is controlled by the Electronic Control Module (ECM) to regulate the International maxforce spn 164 fmi 16SPN 164 FMI 16 indicates a turbocharger boost pressure fault, often caused by leaks in the intake system, faulty wastegate actuator, or clogged EGR valve. pdf), Text File (. Detroit DD15 GHG14 (2014-16) Fault Code: SPN 164 FMI 15 (MCM) Rail Pressure Deviation Greater Than 200 Bar While Under Load DESCRIPTION: Fuel rail pressure deviation under load. Inspect the MCM 120-pin connector and the 120-pin harness connector for signs of corrosion, spread, unseated (pushed out) or damaged pins, connector seal for damage (signs of water or oil . All Forums Professional Garage Enter Forum: Professional Garage Maxxforce DT with extended or no start New Topic Reply to Topic Printer Friendly The code comes up as undefined spn 164 fmi 2. 2007 Maxxforce is different than 2010 and this will happen. SPN: 164 FMI: 18 MaxxForce DT (2010 & Newer) by Tienda de eliminación de DPF | Jul 10, 2023 | Uncategorized | 0 comments Applies To: 2010 MaxxForce DT 9 and 10 DESCRIPTION ber. Replaced all 6 adapters and 6 injectors and ICP sensor. Check wiring harnesses for damage or corrosion, and test the sensor voltage Got a 2012 Maxxforce DT9 throwing a 164 13 code for ICP adaptation in-range fault. Code 164-16 sets for ICP pressure above desired level.